Several installation methods of wall decorative glass mirrors
Fanyu
www.glass.com.cn
2018-01-04 14:50:21
Wall Glass Decorative mirror of the general installation of a fixed method of three, namely, nail-solid method, paste method and the method of embedded pressure.
1. Nail Solid method
This method is to use screws to fix the wall glass decorative mirror on the wall surface (or cylindrical, top) base. The specific steps are as follows:
(1) wall surface treatment wall requirements, no drum belly, uneven, if the wall smoothness can be directly used for installation; otherwise, the use of cement mortar (such as the right to add the appropriate amount of moisture-proof powder effect better), scraping leveling again.
(2) hole drilling every wall glass decorative mirror on the need to drill out of four installation of fixed holes, the hole should be evenly distributed, not too close to the edge of the mirror to prevent cracking. Now the market on the sale of the stereotypes wall glass decorative mirrors have generally been installed holes, amorphous glass can be in the professional processing point punch.
Place the glass mirror on the wall and then place the mirror in the corresponding position of the wall. Through the holes in the glass mirror, its corresponding hole in the wall, remove the mirror, with an electric drill or hammer on the wall marked on the location of the hole, the aperture should be based on the choice of screw size to determine, generally less than 3 mm diameter screw end head.
(3) Paving gasket material in order to prevent the wall caused by uneven grassGlass Decorative MirrorDamaged, should be in the mirror and the wall between the addition of a cushion material. Lining heat materials preferably use thin felt or sponge plate elastomer, 2~3 mm thick, with white glue point glued fixed on the wall, the size of the gasket material is less than glass 10~15 mm, so that after the mirror installation, with caulking paste closed around.
(4) Installation of glass mirror before installation, should be in the back of the glass mirror paste a layer of Kraft paper protection. The specific method is, first in the mirror brushing a layer of white gum, and then a piece of kraft paper pasted on the back of the mirror, and then scrape with plastic plate flat. In the wall of the hole in the embedded plastic expansion bolts, the mirror to the good hole in place, with screws fixed, diagonal tightening, to glass mirror smooth without shaking is advisable.
(5) Closed around the glass installation fixed, in order to prevent moisture intrusion into the mirror behind, affecting the life and quality of the mirror, should use the caulking paste to the mirror and wall between the gap embedded dense.
2. Paste method
Using adhesive with high bonding strength, the glass mirror is pasted directly on the base of the wall. This method is suitable for the installation of wall surface within 1 square meters. If the mirror size is larger, or the ceiling is installed in the mirror, it is best to use the paste and nail solid combination method to ensure that a mirror damage, will not fall hurt people.
The details of the paste are as follows: Clean the back of the mirror and remove the dust and sand. Paste a layer of Kraft paper on the back of the mirror as a protective layer. And then on the mirror on the back of the Kraft paper and on the sagged surface brushing universal glue, when the glue surface does not stick to the hand, the glass mirror in advance by the position line directly pasted on the wall. Press the mirror with your hand so that it is tightly bonded to the wall and notice the pasting at the corners. When the mirror is glued, close the perimeter with the caulking ointment.
It should be noted that in the paste mirror before, should ensure that the wall level, or should be used cement mortar scraping smooth. In addition, adhesive can not be coated directly on the back of the mirror to prevent corrosion damage to the mirror coating.
In addition, in addition to using adhesive adhesive, you can also use double-sided tape to paste the mirror. This double-sided tape is coated on both sides of the sponge plate made of High-strength self-adhesive, about 2-3 mm thick, there is a certain elasticity. When used, cut to 5-10 cm wide strip, first tore off the side of the protective paper, pasted on the wall base, hand press tight, so that the mirror and adhesive tape. Then use the caulking paste to insert the enclosed mirror.
3. The method of inserting pressure
The method is to use stainless steel, aluminum alloy or wood line to do the glass mirror frame, with the nail-solid method of the first frame and the wall base fixed, and then set the glass mirror embedded in the frame. This method is suitable for large-area glass mirror mounting and fixing.
The specific practice of the embedded pressure is as follows: first, by the border of the size of the bullet line, hole, drill. Press the good line first fixed the lower frame layering, the nail spacing to 10-15 centimeters, to increase the bottom support strength. Then paste the blanket on the base with milky white glue. And then set the mirror in the lower frame of the layering, find the wall with the surface of the flat, installation of the upper border and the two sides of the border layering. It should be noted that in the fixed wood layering, it is best to use 20~25mm nail gun to fix, to avoid the use of ordinary round nails, to prevent in the nail layering when the mirror broken.
In addition to the use of nail-free technology mosaic, the specific approach is to use wood-lined card glass mirror, and then use the adhesive stainless steel or aluminum alloy layering sticking on the wood lining, and then in the layering and glass mirror between the corner of the glass glue.
1. Nail Solid method
This method is to use screws to fix the wall glass decorative mirror on the wall surface (or cylindrical, top) base. The specific steps are as follows:
(1) wall surface treatment wall requirements, no drum belly, uneven, if the wall smoothness can be directly used for installation; otherwise, the use of cement mortar (such as the right to add the appropriate amount of moisture-proof powder effect better), scraping leveling again.
(2) hole drilling every wall glass decorative mirror on the need to drill out of four installation of fixed holes, the hole should be evenly distributed, not too close to the edge of the mirror to prevent cracking. Now the market on the sale of the stereotypes wall glass decorative mirrors have generally been installed holes, amorphous glass can be in the professional processing point punch.
Place the glass mirror on the wall and then place the mirror in the corresponding position of the wall. Through the holes in the glass mirror, its corresponding hole in the wall, remove the mirror, with an electric drill or hammer on the wall marked on the location of the hole, the aperture should be based on the choice of screw size to determine, generally less than 3 mm diameter screw end head.
(3) Paving gasket material in order to prevent the wall caused by uneven grassGlass Decorative MirrorDamaged, should be in the mirror and the wall between the addition of a cushion material. Lining heat materials preferably use thin felt or sponge plate elastomer, 2~3 mm thick, with white glue point glued fixed on the wall, the size of the gasket material is less than glass 10~15 mm, so that after the mirror installation, with caulking paste closed around.
(4) Installation of glass mirror before installation, should be in the back of the glass mirror paste a layer of Kraft paper protection. The specific method is, first in the mirror brushing a layer of white gum, and then a piece of kraft paper pasted on the back of the mirror, and then scrape with plastic plate flat. In the wall of the hole in the embedded plastic expansion bolts, the mirror to the good hole in place, with screws fixed, diagonal tightening, to glass mirror smooth without shaking is advisable.
(5) Closed around the glass installation fixed, in order to prevent moisture intrusion into the mirror behind, affecting the life and quality of the mirror, should use the caulking paste to the mirror and wall between the gap embedded dense.
2. Paste method
Using adhesive with high bonding strength, the glass mirror is pasted directly on the base of the wall. This method is suitable for the installation of wall surface within 1 square meters. If the mirror size is larger, or the ceiling is installed in the mirror, it is best to use the paste and nail solid combination method to ensure that a mirror damage, will not fall hurt people.
The details of the paste are as follows: Clean the back of the mirror and remove the dust and sand. Paste a layer of Kraft paper on the back of the mirror as a protective layer. And then on the mirror on the back of the Kraft paper and on the sagged surface brushing universal glue, when the glue surface does not stick to the hand, the glass mirror in advance by the position line directly pasted on the wall. Press the mirror with your hand so that it is tightly bonded to the wall and notice the pasting at the corners. When the mirror is glued, close the perimeter with the caulking ointment.
It should be noted that in the paste mirror before, should ensure that the wall level, or should be used cement mortar scraping smooth. In addition, adhesive can not be coated directly on the back of the mirror to prevent corrosion damage to the mirror coating.
In addition, in addition to using adhesive adhesive, you can also use double-sided tape to paste the mirror. This double-sided tape is coated on both sides of the sponge plate made of High-strength self-adhesive, about 2-3 mm thick, there is a certain elasticity. When used, cut to 5-10 cm wide strip, first tore off the side of the protective paper, pasted on the wall base, hand press tight, so that the mirror and adhesive tape. Then use the caulking paste to insert the enclosed mirror.
3. The method of inserting pressure
The method is to use stainless steel, aluminum alloy or wood line to do the glass mirror frame, with the nail-solid method of the first frame and the wall base fixed, and then set the glass mirror embedded in the frame. This method is suitable for large-area glass mirror mounting and fixing.
The specific practice of the embedded pressure is as follows: first, by the border of the size of the bullet line, hole, drill. Press the good line first fixed the lower frame layering, the nail spacing to 10-15 centimeters, to increase the bottom support strength. Then paste the blanket on the base with milky white glue. And then set the mirror in the lower frame of the layering, find the wall with the surface of the flat, installation of the upper border and the two sides of the border layering. It should be noted that in the fixed wood layering, it is best to use 20~25mm nail gun to fix, to avoid the use of ordinary round nails, to prevent in the nail layering when the mirror broken.
In addition to the use of nail-free technology mosaic, the specific approach is to use wood-lined card glass mirror, and then use the adhesive stainless steel or aluminum alloy layering sticking on the wood lining, and then in the layering and glass mirror between the corner of the glass glue.